Skip to content

Perpetual Wearable Biosensing with Andy Kong

September 10, 2026 · 1 h 6 min

Show notes

Chris welcomes Andy Kong to discuss “Chargerless” and how to build ultra-low-power wearable health trackers that never need wall charging. (00:00:15)

From Hacker Mindset to Startup Founder: They discuss Andy’s background in biosensing, staying with Samy Kamkar, and bringing a pragmatic “get things done” hacker mindset to founding Chargerless in San Francisco, as documented on Andy’s personal website. (00:02:10)

Solving the Wearable Charging Bottleneck: Andy explains how frustration with daily Apple Watch charging led him to design a wearable requiring only one minute of daily sunlight exposure, noting that modern wearables are bottlenecked by battery volume rather than logic chip size. (00:04:30)

Deliberately Underpowered MCUs: Chris and Andy explore system architecture trade-offs, focusing on Chargerless’s choice of an underpowered microcontroller paired with lean firmware rather than feature-heavy, power-hungry processors. (00:07:15)

Intelligent Sampling vs. Continuous Monitoring: They contrast Whoop and Apple Watch’s continuous PPG power drain with Chargerless’s periodic sampling approach, which reserves high-frequency tracking for active workout modes. (00:09:45)

The Limits of Commercial Sensor ICs: Why off-the-shelf health ICs from TI and Analog Devices consumed 100 times too much power due to unoptimized ADCs, inefficient amplifiers, and fixed pulse timings. (00:12:20)

EKG vs. Wrist PPG: Explaining how multi-lead chest EKGs measure electrical heart potential vectors, whereas wrist Photoplethysmography (PPG) uses green light reflection to detect oxygenated blood volume changes. (00:15:05)

Badge Life and DIY Biometrics: Chris and Andy reminisce about community hardware projects like Chaos Camp’s Card10 EKG badge, Kerry Scharfglass’s IR-synchronized dragonfly badge, and Chris’s earlobe PPG sensor that flashed LEDs inside a Solo cup based “badge”. (00:17:50)

Custom Discrete PPG Frontend: How Andy replaced commercial ICs with a discrete circuit that strobes a green LED 50 times per second for microsecond bursts, cycling both the LED and transimpedance amplifier. (00:20:40)

Eliminating Decoupling Lag: Stripping decoupling capacitors removed turn-on delays, while using two amplifier stages avoided high-capacitance digital potentiometers. (00:23:10)

Pivoting Away from BCI: Andy describes his college research on brain-computer interfaces (BCIs) with OpenBCI and why he abandoned non-invasive EEG due to microvolt-level signal noise from cable movement. (00:25:55)

Quantified Self & Personal Informatics: Discussing how self-trackers capture environmental data to identify root causes of complex health symptoms. (00:28:30)

Low-Power Bluetooth Data Batching: How Bluetooth Low Energy accounts for less than 5% of overall power draw by batching 10 KB payloads every 10 minutes for fast burst transmissions to the phone. (00:31:15)

Form Factors and Ring Safety: Comparing Whoop, Oura, Garmin, and Fitbit Air trackers, while covering smart ring battery constraints, Samsung battery recall testing, and degloving risks. (00:34:00)

Whoop’s Slide-On Battery: How Whoop designed a slide-on battery pack to charge while being worn, avoiding the user drop-off caused when devices are taken off to charge. (00:36:45)

Solar Harvesting & Laser Dicing: Chargerless uses boost converters to harvest power from amorphous solar cells, which Andy initially custom diced with laser cutters at MIT. (00:39:20)

Bare-Metal Registers & 28-Hour Days: Transitioning from dev boards to custom PCBs required low-level MCU register programming, custom Makefiles, and a 28-hour daily cycle sleep study in tinfoiled rooms. (00:42:10)

Pricing & Open Data Access: Chargerless is rolling out a pre-production run of a few hundred units for $199 with no subscription fees on getchargerless.com and open data export capabilities. (00:45:00)

Power Over Skin (Body Channel Communication): Andy breaks down his Power over Skin research project, which sends 40–100 MHz RF power safely through human skin using the body as an antenna. (00:47:45)

Microwatt Energy Harvesting: Utilizing Skyworks low-forward-drop diodes, tank circuits, and rectifiers to harvest microwatts for powering LED earrings, ring joysticks, and skin patches. (00:50:30)

All episodes of The Amp Hour

Settings

Display

Language

Decides which stations you see first on the home page.

History

Recently played stations and episodes and your latest searches are only stored in this browser.

Notifications

A short notice when a podcast you follow has a new episode. Turn off single podcasts with the bell on their page.

Account

Save favorites – in the app and on the website.

Keyboard shortcuts

/
Open search
Space
Play or pause
← →
In the player: back 15 s, forward 30 s (episodes) · in a row: next tile
↑ ↓
In a row: target within the tile
Home / End
In a row: first or last tile
Esc
Close window or menu
?
This overview
Now playing

Go to station page

Play next

    Add episodes with “Play next” – they play after the current episode.